How To Reset CMOS for Clearing Computer BIOS

How To Reset CMOS for Clearing Computer BIOS

Hello Geeky, so today we are focusing on How To Reset CMOS for Clearing Computer BIOS. So please read this tutorial carefully so you may comprehend it in a better helpful way.

Guide: How To Reset CMOS for Clearing Computer BIOS

Turn off CMOS on your motherboard and reset the BIOS settings to factory errors, which are settings that the motherboard manufacturer thinks is appropriate for most users. One reason to remove CMOS is to assist in troubleshooting or resolving certain computer problems or hardware compatibility issues. In most cases, simply configuring the BIOS is enough to get a PC seemingly dead up and running again.

You may also want to clear CMOS to reset the BIOS or system password, or if you have made changes to the BIOS that you suspect have caused a problem. Three different methods for CMOS elimination are described below. Each method is as good as any other, but you may find one of them easier, or the difficulty you have may limit it to CMOS elimination in a specific way.

How to reset your CMOS for Computer BIOS elimination

Repair your CMOS with one case Button

  • Turn off your computer.
  • Disconnect your computer from the wallpaper. You can unplug the power from the back of your power supply or from the wall outlet.
  • Find out the case button marked “Clear” or “Configure.” It is normally near or near the force button.
  • Disable “Delete” or “Reset” button down for five to ten seconds, then release. You may need to use a pencil sharpener to hold it down button if it is small.
  • Restart your computer and reboot.
  • Press the right key to enter your BIOS options. Depending on your motherboard, it can be., Delete, F2, F8 or F12. Different operating systems use different keys, or you can set Windows 10 to boot into your BIOS for you.
  • Adjust your BIOS options as needed. Some motherboards have the option to load “optimized defaults,” which is a great start.

Fix your CMOS with a motherboard Button

  • Turn off your computer.
  • Disconnect your computer from the wallpaper. You can unplug the power from the back of your power supply or from the wall outlet.
  • Enter the power of the case button multiple times to discharge any motherboard capacitors.
  • Find the right thing button on your motherboard. If you are not sure where to find it, check your motherboard script. You can find these on your motherboard manufacturer’s or computer manufacturer’s website.
  • Press and hold button for five to ten seconds with your finger or the eraser end of a pencil. If you use your finger, make sure you reach for it by tapping the metal floor (the doors are large) before touching anything in your computer.
  • Restart your computer and reboot.
  • Press the right key to enter your BIOS options.
  • Adjust your BIOS options as needed.

Reset your CMOS by restarting the CMOS Battery

  • Turn off your computer.
  • Disconnect your computer from the wallpaper.
  • Enter the power button multiple times to clear any capacitors.
  • Locate the CMOS battery on your motherboard. This is a very large CR2032 battery, a battery worth about as shown below. You will find near PCI Express slots on most motherboards. Consult your motherboard’s manual for its exact location.
  • remove the CMOS battery. If secured by a metal clip, simply remove the battery from the bottom of the clip. Be careful not to touch the clip.
  • Wait a few minutes, then replace the CMOS battery.
  • Restart your computer.

Reset your CMOS with Jumper Motherboard

  • Turn off your computer.
  • Disconnect your computer from the wallpaper.
  • Enter the power button multiple times to clear any capacitors.
  • Open your computer box and find the CMOS emission pins. There will usually be a two- or three-way configuration installed on the motherboard marked “CLEAR,” “TTUN,” or even “CLRPWD” for “clear password.”
  • On a three-pin configuration with a split center pin, lift the plastic screw up to attach the center pin and the previously disconnected pin. For a two-pin configuration, remove the jump completely.
  • Wait a few minutes, then return the jumper to its original setting.
  • Restart your computer.

Faq

Guide about How To Reset CMOS for Clearing Computer BIOS


In this guide, we told you about the How To Reset CMOS for Clearing Computer BIOS; please read all steps above so that you understand How To Reset CMOS for Clearing Computer BIOS in case if you need any assistance from us, then contact us.

How this tutorial or guide assisting you?


So in this guide, we discuss the How To Reset CMOS for Clearing Computer BIOS, which undoubtedly benefits you.



Final note

I hope you like the guide How To Reset CMOS for Clearing Computer BIOS. In case if you have any queries regards this article/tutorial you may ask us. Also, please share your love by sharing this article with your friends and family.

Trickbugs: Get the latest Trick and Tips
Logo
Enable registration in settings - general